| myArmoury.com is now completely member-supported. Please contribute to our efforts with a donation. Your donations will go towards updating our site, modernizing it, and keeping it viable long-term.
Last 10 Donors: Graham Shearlaw, Anonymous, Daniel Sullivan, Chad Arnow, Jonathan Dean, M. Oroszlany, Sam Arwas, Barry C. Hutchins, Dan Kary, Oskar Gessler (View All Donors) |
| Author |
Message |
|
Sam Arwas
Location: Australia Joined: 02 Dec 2015
Posts: 92
|
 Posted: Mon 18 Feb, 2019 3:55 pm Post subject: Clicking grip- what type of adhesive to fix? |
 |
|
|
I've heard some people have had success fixing a clicking grip by fixing the sword in place point-up and pouring thread locker adhesive down the fuller. I'm assuming that it runs between the broken peices of epoxy and locks them in place. But when I search "loctite adhesive" I see a whole bunch of different types and I'm only going to get one shot at this.
|
|
  |
 |
Ian Hutchison
Location: Louisiana / Nordrhein-Westholland Joined: 27 Nov 2007
Posts: 626
|
| Posted: Mon 18 Feb, 2019 4:35 pm Post subject: |
|
|
Perhaps loctite threadlocker? It comes in red and blue varieties iirc. One is stronger than the other. It is not permanent, not like loctite epoxy, so it might be worth a try. It's quite runny, so after letting it fill the gaps, you might want to lay the sword horizontal, then flip it after a minute or two.
'We are told that the pen is mightier than the sword, but I know which of these weapons I would choose.' - Adrian Carton de Wiart
|
|
|
|
|
|
Sam Arwas
Location: Australia Joined: 02 Dec 2015
Posts: 92
|
| Posted: Mon 18 Feb, 2019 5:22 pm Post subject: |
|
|
| Ian Hutchison wrote: | | Perhaps loctite threadlocker? It comes in red and blue varieties iirc. One is stronger than the other. It is not permanent, not like loctite epoxy, so it might be worth a try. It's quite runny, so after letting it fill the gaps, you might want to lay the sword horizontal, then flip it after a minute or two. |
But wouldn't that cause gravity to make it run back out of the fuller?
|
|
|
|
|
Glen A Cleeton
|
| Posted: Tue 19 Feb, 2019 5:18 am Post subject: |
|
|
Be more specific and explain which sword exactly you are having an issue with.
I use a lot of runny superglue and it sets quite quickly, removing a lot of wiggles.
Some swords can be easily fixed with no glue solutions but again, you have not mentioned what sword is to be addressed.
|
|
|
|
|
|
Sam Arwas
Location: Australia Joined: 02 Dec 2015
Posts: 92
|
| Posted: Tue 19 Feb, 2019 2:54 pm Post subject: |
|
|
| Glen A Cleeton wrote: | Be more specific and explain which sword exactly you are having an issue with.
I use a lot of runny superglue and it sets quite quickly, removing a lot of wiggles.
Some swords can be easily fixed with no glue solutions but again, you have not mentioned what sword is to be addressed. |
it's an Albion Knight. I've tried shaking it laterally like manufacturer suggested but no luck. They offered to fix it if I can't but I'd rather avoid shipping it across the world if I can.
|
|
|
|
|
Ian Hutchison
Location: Louisiana / Nordrhein-Westholland Joined: 27 Nov 2007
Posts: 626
|
| Posted: Tue 19 Feb, 2019 5:19 pm Post subject: |
|
|
| Sam Arwas wrote: | | Ian Hutchison wrote: | | Perhaps loctite threadlocker? It comes in red and blue varieties iirc. One is stronger than the other. It is not permanent, not like loctite epoxy, so it might be worth a try. It's quite runny, so after letting it fill the gaps, you might want to lay the sword horizontal, then flip it after a minute or two. |
But wouldn't that cause gravity to make it run back out of the fuller? |
Ah, I misunderstood where you were applying it.
In that case, yes, just keep it in an upright position.
'We are told that the pen is mightier than the sword, but I know which of these weapons I would choose.' - Adrian Carton de Wiart
|
|
|
|
|
Glen A Cleeton
|
| Posted: Tue 19 Feb, 2019 8:37 pm Post subject: |
|
|
Yes, glue is the easiest. William's reply elsewhere speaks of his adventures and in other threads here. Alternately, there is jamming splints up the fuller but that can be unsightly.
I love superglue and actually prefer the runny stuff unless building up a large crater or something. Fingernail polish remover softens the gule for removal of spills. Just try small amounts first. I would suggest it is the grip core and cross interplay and both just shy of tight. Theoretically on an Albion, the cross should have been pounded on tight and should not be moving. I fear that is rarely the case and the nature of the two piece grip always allows some clearances. Even minute motion of the two can create the clicking, or tinking noises.
Worst case, rebuild it by removing the grip, "staking" the guard if a loose fit to the blade or horrors, add shims or weld/braze/solder buildup to make the hole smaller.
Or, glue to suit 
Cheers
GC
|
|
|
|
|
|
Sam Arwas
Location: Australia Joined: 02 Dec 2015
Posts: 92
|
| Posted: Tue 19 Feb, 2019 9:33 pm Post subject: |
|
|
| Glen A Cleeton wrote: | Yes, glue is the easiest. William's reply elsewhere speaks of his adventures and in other threads here. Alternately, there is jamming splints up the fuller but that can be unsightly.
I love superglue and actually prefer the runny stuff unless building up a large crater or something. Fingernail polish remover softens the gule for removal of spills. Just try small amounts first. I would suggest it is the grip core and cross interplay and both just shy of tight. Theoretically on an Albion, the cross should have been pounded on tight and should not be moving. I fear that is rarely the case and the nature of the two piece grip always allows some clearances. Even minute motion of the two can create the clicking, or tinking noises.
Worst case, rebuild it by removing the grip, "staking" the guard if a loose fit to the blade or horrors, add shims or weld/braze/solder buildup to make the hole smaller.
Or, glue to suit
Cheers
GC |
I sent a video recording of it to Albion and they believe it's just a broken chunk of epoxy shifting around inside the grip. It didn't ship with this noise, it started after some light test cutting.
|
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
All contents © Copyright 2003-2024 myArmoury.com — All rights reserved
Discussion forums powered by phpBB © The phpBB Group
Switch to the Basic Low-bandwidth Version of the forum
|
This is a standard topic