Info Favorites Register Log in
myArmoury.com Discussion Forums

Forum index Memberlist Usergroups Spotlight Topics Search
Forum Index > Historical Arms Talk > Messer questions Reply to topic
This is a standard topic  
Author Message
Shawn Duncanson




Location: Spokane Wa
Joined: 05 Dec 2003

Posts: 49

PostPosted: Thu 20 Mar, 2014 7:17 pm    Post subject: Messer questions         Reply with quote

Looking at pics of how they were used they seem to me to be more for slicing and draw cutting. In some plates is shows severed hands and and such but with the grappling and slicing and cutting of lighter targets such as hands. Were they thinner in a distal taper sort of way or did they have a fat spine like a falchion? Thanks guys.
Not all who wander are lost.
View user's profile Send private message
Luka Borscak




Location: Croatia
Joined: 11 Jun 2007
Likes: 7 pages

Posts: 2,307

PostPosted: Fri 21 Mar, 2014 4:56 am    Post subject:         Reply with quote

I know more about falchions than about messers, but since I know for sure that at least some falchions had much distal taper and not very thick spines at the CoP, I would guess that would be true also for messers...
View user's profile Send private message
Chris Friede




Location: Austin
Joined: 15 Mar 2014

Posts: 39

PostPosted: Fri 21 Mar, 2014 9:15 am    Post subject:         Reply with quote

Oskar Hasselhoff offers Grossmesser training (Hollow Earth made some customized wooden trainers for him). His techniques do focus on cuts from the wrist directed at opponent wrists and arms. If the trainers are accurate, they exhibit very little distal taper until the clipped point...

Very interesting fighting technique to watch.
View user's profile Send private message
Kevin Colwell
Industry Professional



Location: Connecticut
Joined: 15 Dec 2011

Posts: 24

PostPosted: Tue 25 Mar, 2014 4:01 am    Post subject:         Reply with quote

the few I have seen have a non-linear distal taper ( a lot like dao, actually). The area near the forte is quite thick, with almost no taper for about 3-4 inches. Then there is rapid taper for the next 6 inches or so. The blade tapers very slightly after that until the clip. At the clip, the taper becomes rapid again until the point.

hope this helps. Think of the blade as having different zones, with each adapted to specific uses.

they are quite complex instruments, and far from just a sharpened bar of steel.

take care,
kc

If there is a lower class, I am in it
If there is a criminal element, I am of it
If there is a soul in prison, I can not be free!

E V Debs
View user's profile Send private message
Timo Nieminen




Location: Brisbane, Australia
Joined: 08 May 2009
Likes: 1 page
Reading list: 1 book

Posts: 1,504

PostPosted: Tue 25 Mar, 2014 3:19 pm    Post subject:         Reply with quote

There are others (both messers and falchions - and Chinese dao, too) that have very little distal taper, instead having a blade that is very thin along the whole length (say, 3-4mm, or even under 2mm). One can't really generalise in much detail about such broad categories. There's lots of diversity.
"In addition to being efficient, all pole arms were quite nice to look at." - Cherney Berg, A hideous history of weapons, Collier 1963.
View user's profile Send private message Visit poster's website
Shawn Duncanson




Location: Spokane Wa
Joined: 05 Dec 2003

Posts: 49

PostPosted: Fri 28 Mar, 2014 4:59 pm    Post subject:         Reply with quote

Thanks a bunch guys, I have owned a dao in the past like some of you reference. It was a decent chopper though I would not say a dedicated one and the broad curved tip made for a good tip slicer/ draw cutter.

Also whats with the disembodied hand in this slide?
http://daten.digitale-sammlungen.de/~db/bsb00...p;seite=69

Not all who wander are lost.
View user's profile Send private message
Victor Sloan




Location: North Carolina
Joined: 15 Feb 2014

Posts: 69

PostPosted: Sat 29 Mar, 2014 5:33 am    Post subject:         Reply with quote

I do not know about the slide specifically but it appears to be pointing to some very important detail which is probably described in the text.
Looking to start HEMA!
View user's profile Send private message Send e-mail


Display posts from previous:   
Forum Index > Historical Arms Talk > Messer questions
Page 1 of 1 Reply to topic
All times are GMT - 8 Hours

View previous topic :: View next topic
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum






All contents © Copyright 2003-2024 myArmoury.com — All rights reserved
Discussion forums powered by phpBB © The phpBB Group
Switch to the Basic Low-bandwidth Version of the forum