Info Favorites Register Log in
myArmoury.com Discussion Forums

Forum index Memberlist Usergroups Spotlight Topics Search
Forum Index > Makers and Manufacturers Talk > circa 1600 sword breaker Reply to topic
This is a standard topic  
Author Message
Leo Todeschini
Industry Professional



Location: Oxford, UK
Joined: 12 Nov 2006
Likes: 1 page

Spotlight topics: 1
Posts: 1,723

Feedback score: 100%
(3 total ▮ 100% positive)
PostPosted: Thu 01 Aug, 2013 2:38 pm    Post subject: circa 1600 sword breaker         Reply with quote

Hi All,

I have just finished this sword breaker based on a composite of pieces from around 1600 and I hope you like the result.

This style of knife came in at the end of the 16thC and lasted perhaps as late as the mid 17th and were used defensively to trap an opponents blade and take control of it and they do this very well. When a blade enters the void between the teeth, a pull or a twist will catch the and hold the blade. Whether they truly did 'break blades' I am not so sure, but they certainly do work.

They were not a very common form of knife and perhaps this was ether because they were bulky or expensive to make or indeed deemed to not be very useful however they are certainly very striking. The teeth were either fixed like this example or were articulated and must have been very much more expensive. They do look inherently weak, but this is partially offset by a thick blade with very little distal taper.

This example has a 6.5mm/ 1/4" thick blade, 275mm long/11.5" and has a steel guard and pommel with a steel and bronze wrapped grip with steel turks heads top and bottom.

Tod



 Attachment: 162.58 KB
IMGP1704.JPG


 Attachment: 136.76 KB
IMGP1707.JPG


 Attachment: 137.38 KB
IMGP1708.JPG


 Attachment: 185.41 KB
IMGP1709.JPG


 Attachment: 170.86 KB
IMGP1710.JPG


 Attachment: 146.27 KB
IMGP1711.JPG


www.todsworkshop.com
www.todcutler.com
www.instagram.com/todsworkshop
https://www.facebook.com/TodsWorkshop
www.youtube.com/user/todsstuff1
View user's profile Send private message Visit poster's website
Boris Bedrosov
Industry Professional



Location: Bourgas, Bulgaria
Joined: 06 Nov 2005

Posts: 700

Feedback score: None
PostPosted: Thu 01 Aug, 2013 2:51 pm    Post subject: Re: circa 1600 sword breaker         Reply with quote

Leo Todeschini wrote:
...... and I hope you like the result.......


Of course, we like it - excellent masterpiece as usual.

When I saw the pictures, but before reading your text, a couple of questions rose in my mind. Just a bit latter I saw you've answered to all of them.
For now, I have just one, purely technological question - how the ring is attached to the guard? It seems that the easiest way are integral pins, riveted at the other side, but there could be (in my opinion) at least a couple of other ways.
Of course, I hope this is not a craftsman's secret!

"Everyone who has the right to wear a long sword, has to remember that his sword is his soul,
and he has to separate from it when he separates from his life"
Tokugawa Ieyasu

Find my works on Facebook:
Boris Bedrosov's Armoury
View user's profile Send private message Visit poster's website
Patrick Kelly




Location: Wichita, Kansas
Joined: 17 Aug 2003
Reading list: 42 books

Spotlight topics: 2
Posts: 5,739

Feedback score: 100%
(6 total ▮ 100% positive)
PostPosted: Thu 01 Aug, 2013 5:39 pm    Post subject:         Reply with quote

Outstanding work. I have a particular fondness for these daggers and yours is a beautiful rendition.
"In valor there is hope.".................. Tacitus
View user's profile Send private message AIM Address
Mark Moore




Location: East backwoods-assed Texas
Joined: 01 Oct 2003
Likes: 6 pages
Reading list: 1 book

Posts: 2,294

Feedback score: None
PostPosted: Thu 01 Aug, 2013 9:45 pm    Post subject:         Reply with quote

I guess you know....Down here in Texas, we call that a saw-back Bowie knife..... Razz .......Just kidding! Fantastic work! Laughing Out Loud ...McM
View user's profile Send private message
Marik C.S.




Location: Germany
Joined: 16 Feb 2010

Posts: 163

Feedback score: None
PostPosted: Thu 01 Aug, 2013 11:00 pm    Post subject:         Reply with quote

Mark Moore wrote:
I guess you know....Down here in Texas, we call that a saw-back Bowie knife..... Razz .......Just kidding! Fantastic work! Laughing Out Loud ...McM


You are a very bad person, now I want to see a 17th Century version of Rambo with such a knife Big Grin

That dagger is awesome, would it be honed to a full edge and completely sharpened seeing as it is mainly used for parrying and controlling the opponents blade?

Europe - Where the History comes from. - Eddie Izzard
View user's profile Send private message Visit poster's website ICQ Number
Patrick Kelly




Location: Wichita, Kansas
Joined: 17 Aug 2003
Reading list: 42 books

Spotlight topics: 2
Posts: 5,739

Feedback score: 100%
(6 total ▮ 100% positive)
PostPosted: Fri 02 Aug, 2013 12:42 am    Post subject:         Reply with quote

Leo,

Where did you get the inspiration for the scabbard? I've never seen a photograph of a surviving specimen. I'd love to see one if you have it.

"In valor there is hope.".................. Tacitus
View user's profile Send private message AIM Address
Leo Todeschini
Industry Professional



Location: Oxford, UK
Joined: 12 Nov 2006
Likes: 1 page

Spotlight topics: 1
Posts: 1,723

Feedback score: 100%
(3 total ▮ 100% positive)
PostPosted: Fri 02 Aug, 2013 1:04 am    Post subject:         Reply with quote

Thanks all for your comments - I really appreciate the kind words.

Boris Bedrosov wrote
Quote:
For now, I have just one, purely technological question - how the ring is attached to the guard? It seems that the easiest way are integral pins, riveted at the other side, but there could be (in my opinion) at least a couple of other ways.
Of course, I hope this is not a craftsman's secret!


This is in fact a casting, but I made the master in steel as I often prefer to do this rather than wax if I am going this route. The master was fabricated with the arms and block forming one piece and the ring brazed on as a second. This is the normal method of construction.

Patrick Kelly wrote
Quote:
Where did you get the inspiration for the scabbard? I've never seen a photograph of a surviving specimen. I'd love to see one if you have it.


I will have to disappoint you I am afraid. I also have never seen a scabbard for one of these, so this has to be conjecture. A chape on a clipped point looks weird if it is conical, so I tend to favour the form I have used here and you see this historically on falchions etc. The locket is a usual wrapped and soldered form and as this was for a lady I cheesily used the heart motif - fitting anyway, but perhaps more so because she asked for a 'feminine sword breaker' - if that is not a contradiction!

The decoration is acanthus leaf vines and that is a timeless motif. I made one of these knives 15 years ago and tried to use an all leather scabbard and it just tended to bind and didn't really work, so I chose a wood cored scabbard this time.

Tod

www.todsworkshop.com
www.todcutler.com
www.instagram.com/todsworkshop
https://www.facebook.com/TodsWorkshop
www.youtube.com/user/todsstuff1
View user's profile Send private message Visit poster's website
Patrick Kelly




Location: Wichita, Kansas
Joined: 17 Aug 2003
Reading list: 42 books

Spotlight topics: 2
Posts: 5,739

Feedback score: 100%
(6 total ▮ 100% positive)
PostPosted: Fri 02 Aug, 2013 9:49 am    Post subject:         Reply with quote

Well, it's a beautiful piece of conjecture. I particularly like the decorative motif on the scabbard. I assume you use some kind of stamp to form the teeth? How challenging is that? It looks like there would be plenty of opportunity to muck it up and start over.
"In valor there is hope.".................. Tacitus
View user's profile Send private message AIM Address
Boris Bedrosov
Industry Professional



Location: Bourgas, Bulgaria
Joined: 06 Nov 2005

Posts: 700

Feedback score: None
PostPosted: Sat 03 Aug, 2013 6:34 am    Post subject:         Reply with quote

OK!
I guessed about brazing as a variant, but didn't about casting.

Thanks for the answer!

"Everyone who has the right to wear a long sword, has to remember that his sword is his soul,
and he has to separate from it when he separates from his life"
Tokugawa Ieyasu

Find my works on Facebook:
Boris Bedrosov's Armoury
View user's profile Send private message Visit poster's website
Leo Todeschini
Industry Professional



Location: Oxford, UK
Joined: 12 Nov 2006
Likes: 1 page

Spotlight topics: 1
Posts: 1,723

Feedback score: 100%
(3 total ▮ 100% positive)
PostPosted: Sun 04 Aug, 2013 10:47 am    Post subject:         Reply with quote

Patrick Kelly wrote
Quote:
Well, it's a beautiful piece of conjecture. I particularly like the decorative motif on the scabbard. I assume you use some kind of stamp to form the teeth? How challenging is that? It looks like there would be plenty of opportunity to muck it up and start over.


Thank you.

15 years ago I made one of these, by drilling and filing and it took days. I then hardened it and dropped it before tempering - snapped in half and `i swore a great deal. It was not particularly challenging, it just took a long time.

This time I profile cut the blade.

Tod

www.todsworkshop.com
www.todcutler.com
www.instagram.com/todsworkshop
https://www.facebook.com/TodsWorkshop
www.youtube.com/user/todsstuff1
View user's profile Send private message Visit poster's website
Matt Corbin




PostPosted: Sat 14 Sep, 2013 11:52 am    Post subject:         Reply with quote

Hi Tod,

I know this reply is a little late, but that is absolutely stunning Eek! Very nicely done.

It looks quite a lot like this sword breaker from the Wallace Collection


http://www.wallacecollection.org/whatson/treasure/120

“This was the age of heroes, some legendary, some historical . . . the misty borderland of history where fact and legend mingle.”
- R. Ewart Oakeshott
View user's profile Send private message
Leo Todeschini
Industry Professional



Location: Oxford, UK
Joined: 12 Nov 2006
Likes: 1 page

Spotlight topics: 1
Posts: 1,723

Feedback score: 100%
(3 total ▮ 100% positive)
PostPosted: Sun 15 Sep, 2013 8:32 am    Post subject:         Reply with quote

Hi Matt,

Yes this was a major source of inspiration, the two principle differences is that I made mine a little shorter and the grip is not spiral carved.

Tod

www.todsworkshop.com
www.todcutler.com
www.instagram.com/todsworkshop
https://www.facebook.com/TodsWorkshop
www.youtube.com/user/todsstuff1
View user's profile Send private message Visit poster's website
Russ Ellis
Industry Professional



PostPosted: Mon 16 Sep, 2013 6:37 am    Post subject:         Reply with quote

Nice work as always Leo. I've often thought that these sword breakers were evidence that even in the 16th and 17th century there were gadget guys that liked things that had a certain "cool" factor, along the same lines as those "trident" main gauches and a little later the dagger pistols.
TRITONWORKS Custom Scabbards
View user's profile Send private message
Lancelot Chan
Industry Professional



Location: Hong Kong
Joined: 24 Oct 2003
Likes: 2 pages

Posts: 1,307

Feedback score: None
PostPosted: Mon 16 Sep, 2013 7:05 am    Post subject:         Reply with quote

Hello! Nice work Leo! I'm wondering about the teeth. Wouldn't the points of the void area create stress riser and cause problem during heat treat? Or did you made those voids after heat treating the blade? I'm interested to know. Please let us know more about how you approached the heat treatment in prepare with the teeth. Thanks!
Ancient Combat Association —http://www.acahk.org
Realistic Sparring Weapons — http://www.rsw.com.hk
Nightstalkers — http://www.nightstalkers.com.hk
View user's profile Send private message Visit poster's website
Leo Todeschini
Industry Professional



Location: Oxford, UK
Joined: 12 Nov 2006
Likes: 1 page

Spotlight topics: 1
Posts: 1,723

Feedback score: 100%
(3 total ▮ 100% positive)
PostPosted: Mon 16 Sep, 2013 12:46 pm    Post subject:         Reply with quote

Lancelot Chan wrote
Quote:
Hello! Nice work Leo! I'm wondering about the teeth. Wouldn't the points of the void area create stress riser and cause problem during heat treat? Or did you made those voids after heat treating the blade? I'm interested to know. Please let us know more about how you approached the heat treatment in prepare with the teeth. Thanks


In this case the blade was profile cut from steel that was heat treated prior to being cut. However the last one I made was heat treated after the teeth were cut and it did not cause any problems. The cuts in the blade are all radiussed slightly rather than left sharp and this helps.

Thanks for the kind words.

Tod

www.todsworkshop.com
www.todcutler.com
www.instagram.com/todsworkshop
https://www.facebook.com/TodsWorkshop
www.youtube.com/user/todsstuff1
View user's profile Send private message Visit poster's website


Display posts from previous:   
Forum Index > Makers and Manufacturers Talk > circa 1600 sword breaker
Page 1 of 1 Reply to topic
All times are GMT - 8 Hours

View previous topic :: View next topic
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum






All contents © Copyright 2003-2024 myArmoury.com — All rights reserved
Discussion forums powered by phpBB © The phpBB Group
Switch to the Basic Low-bandwidth Version of the forum