| myArmoury.com is now completely member-supported. Please contribute to our efforts with a donation. Your donations will go towards updating our site, modernizing it, and keeping it viable long-term. Last 10 Donors: Daniel Sullivan, Anonymous, Chad Arnow, Jonathan Dean, M. Oroszlany, Sam Arwas, Barry C. Hutchins, Dan Kary, Oskar Gessler, Dave Tonge (View All Donors) |
Author |
Message |
Allan Senefelder
Industry Professional
|
Posted: Fri 20 Jan, 2012 12:38 pm Post subject: FS Merctailor Gorget and Scales |
|
|
Gotta keep feeding the outstanding commisions machine. I have for sale one of the 15/16th century gorgets we used to make. Made from 16 gauge steel with beveled plate edges and rolled edges where appropriate. Closes with a keyslot rivet and pin closures on either side of the top neck lame. If desired I can install straps for the attachement of shoulder harness. Will fit up to an 18 inch neck with room for the collar of an arming garment. I'm thouroughly average at 5 foot 10 inches, 180-185 pounds, not particulally large just average and this fits me fine. Like to get $180 ( less than we used to get for these ) plus the cost of shipping.
I have also been saving scrap from outstanding commision work and had enough around to make 7 dozen of the scales we used to offer. They're 1 1/2 inches wide by 2 inches long, made from 16 gauge steel with a slight 3-4 degree curve to them. Rivets are included. Like to get $25.00 plus shipping ( they'll fit in a small flate rate box for $7.00 ). I'm continuing to save scrape so i'll probably made a few more of these to make use of it.
Feel free to ask any questions. Paypal, check or money order fine.
Attachment: 52.15 KB
Attachment: 52.14 KB
Attachment: 44.44 KB
Attachment: 58.29 KB
|
|
|
|
Allan Senefelder
Industry Professional
|
Posted: Fri 20 Jan, 2012 1:40 pm Post subject: |
|
|
Scales are spoken for.
|
|
|
|
Allen Foster
|
Posted: Fri 20 Jan, 2012 5:36 pm Post subject: Re: FS Merctailor Gorget and Scales |
|
|
Allan Senefelder wrote: | Gotta keep feeding the outstanding commisions machine. I have for sale one of the 15/16th century gorgets we used to make. Made from 16 gauge steel with beveled plate edges and rolled edges where appropriate. Closes with a keyslot rivet and pin closures on either side of the top neck lame. If desired I can install straps for the attachement of shoulder harness. Will fit up to an 18 inch neck with room for the collar of an arming garment. I'm thouroughly average at 5 foot 10 inches, 180-185 pounds, not particulally large just average and this fits me fine. Like to get $180 ( less than we used to get for these ) plus the cost of shipping.
I have also been saving scrap from outstanding commision work and had enough around to make 7 dozen of the scales we used to offer. They're 1 1/2 inches wide by 2 inches long, made from 16 gauge steel with a slight 3-4 degree curve to them. Rivets are included. Like to get $25.00 plus shipping ( they'll fit in a small flate rate box for $7.00 ). I'm continuing to save scrape so i'll probably made a few more of these to make use of it.
Feel free to ask any questions. Paypal, check or money order fine. |
Dibs on the gorget if I can get my spaulders to attach. Allan?
"Rise up, O Lord, and may thy enemies be dispersed and those who hate thee be driven from thy face."
|
|
|
|
Allan Senefelder
Industry Professional
|
Posted: Sat 21 Jan, 2012 8:49 am Post subject: |
|
|
Gorget is sold.
|
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
All contents © Copyright 2003-2024 myArmoury.com All rights reserved
Discussion forums powered by phpBB © The phpBB Group
Switch to the Basic Low-bandwidth Version of the forum
|