Info Favorites Register Log in
myArmoury.com Discussion Forums

Forum index Memberlist Usergroups Spotlight Topics Search
Forum Index > Off-topic Talk > ISO PoleArm Shaft Wood Source for DIY project Reply to topic
This is a standard topic  
Author Message
Chris Arrington





Joined: 06 Apr 2007

Posts: 115

PostPosted: Fri 17 Dec, 2010 12:06 pm    Post subject: ISO PoleArm Shaft Wood Source for DIY project         Reply with quote

Well, I finally got around to ordering my GDFB/Hanwei PoleAxe head.

I am happy with my purchase, even though I find it much lighter and smaller than I thought it would be.

Now my problem is hafting it. In my rural area (WV) there are two sources of wood. Lowe's and Home Depot. I figured I would get 1 1/2" by 1 1/2" by 6 foot. I was looking for Ash, Hickory, or Oak.

Unfortunately, the best I can find is Red Oak 1 1/2" by 1 1/2" in 2 foot lenghts. Or Poplar in 1" by 1 1/2" in longer lengths. From my understanding, the Poplar is not a good choice for a polearm shaft.

Do you guys have any suggestions, or sources of wood shafts from the internet?

Thanks!
View user's profile Send private message
Scott Hrouda




Location: Minnesota, USA
Joined: 17 Nov 2006
Likes: 15 pages
Reading list: 87 books

Posts: 643

PostPosted: Fri 17 Dec, 2010 12:19 pm    Post subject:         Reply with quote

Good afternoon Chris!

Go to the wheelbarrow isle and pick up an ash replacement handle. See the threads below for more information.

Pollaxe/Streithammer Project

Hafting my Poleaxe Head

...and that, my liege, is how we know the Earth to be banana shaped. - Sir Bedevere
View user's profile Send private message
Tjarand Matre




Location: Nøtterøy, Norway
Joined: 19 Sep 2010

Posts: 159

PostPosted: Fri 17 Dec, 2010 12:49 pm    Post subject:         Reply with quote

Poplar grows too fast, it will be wobbly and could snap if you swing the weapon too fast.
For good wood sources, try to tag along on any archery fora, they are usually well informed about sources for ash/yew/elm. If you could pick any wood, I'd go for elm.
View user's profile Send private message Send e-mail
Jean Thibodeau




Location: Montreal,Quebec,Canada
Joined: 15 Mar 2004
Likes: 50 pages
Reading list: 1 book

Spotlight topics: 5
Posts: 8,310

PostPosted: Fri 17 Dec, 2010 1:15 pm    Post subject:         Reply with quote

You could buy hickory hafts from Purpleheart:
http://www.woodenswords.com/WMA/staffs.htm

The quality of the wood wouldn't be in doubt. Wink

If you have a local Eastern martial arts store you could buy a " BO " staff and use it for a spear but if you are looking for oversized ( Over 1 1/8" ) or octagonal hafts it might be more difficult to find.

I've mounted some spear heads on a White Oak Bo staff with good results and reasonable confidence since I have trained with a Bo staff for European quarter staff and they hardly show any signs of impacts after years of use against other staffs of lower quality wood.

You can easily give up your freedom. You have to fight hard to get it back!
View user's profile Send private message
Chris Arrington





Joined: 06 Apr 2007

Posts: 115

PostPosted: Fri 17 Dec, 2010 3:20 pm    Post subject:         Reply with quote

Jean,

I'll check them out, but I was wanting square. Octagonal is a possibility I guess.

Scott,

I remembered you all discussing replacement handles, but when I looked, I thought they were too short. How long are they? I'll look again this weekend.

Thanks guys !
View user's profile Send private message
Scott Hrouda




Location: Minnesota, USA
Joined: 17 Nov 2006
Likes: 15 pages
Reading list: 87 books

Posts: 643

PostPosted: Fri 17 Dec, 2010 4:30 pm    Post subject:         Reply with quote

The wheelbarrow handles are 5 feet (60") long. My finished poleaxe is 5' 7" (67") long. 5 1/2' to 6' is in the right neighborhood for a poleaxe. I would like to get my hands on a copy of Waldman's Hafted Weapons in Medieval and Renaissance Europe: The Evolution of European Staff Weapons between 1200 and 1650 that Chad has recommended.
...and that, my liege, is how we know the Earth to be banana shaped. - Sir Bedevere
View user's profile Send private message
Ron Reuter




Location: Southern Indiana
Joined: 04 Oct 2007

Posts: 56

PostPosted: Fri 17 Dec, 2010 4:33 pm    Post subject:         Reply with quote

Chris,

I also had a hard time finding a haft for my polearm. What I ended up doing was purchasing 2 pieces of oak that measured 1 1/2" x 3/4" (1x2), 6 ft long, and glued them together (lowes). I ended up with a piece of oak 1 1/2" x 1 1/2" inch. I then used a belt sander to quickly size the board to roughly 1 1/2" x 1" . I then used my router and carved 45 degree angle on each corner. The seam is very hard to see. I have included a couple of pictures.





Ron

www.yeoldegaffers.com
View user's profile Send private message Visit poster's website


Display posts from previous:   
Forum Index > Off-topic Talk > ISO PoleArm Shaft Wood Source for DIY project
Page 1 of 1 Reply to topic
All times are GMT - 8 Hours

View previous topic :: View next topic
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum






All contents © Copyright 2003-2024 myArmoury.com — All rights reserved
Discussion forums powered by phpBB © The phpBB Group
Switch to the Basic Low-bandwidth Version of the forum