myArmoury.com - New XII {relatively speaking}

• Info • Register • Log in
• Forum Index • Memberlist • Usergroups • Search • Spotlight Topics • Watched Topics

Forum Index » Makers and Manufacturers Talk » New XII {relatively speaking}

Posts: 870 Location: Seattle area

Thu 31 May, 2007 5:40 pm

New XII {relatively speaking}

This sword, is what you might call a precursor. Its not "permanently assembled", but it has everything else that the permanently assembled swords will have.........

This is a XII, and the blade crossection from the fuller to the tip is lenticular, instead of flat diamond, or hex....This, for me is new........ This new line of swords will be this way, lenticular for the earlier, fullered swords........

Gone is the "wavy" appearance of what was once referred to as the "Dawg Hamon'. Now, just a flat satin finish.........

The edges are convex......... No more the obvious secondary bevei.........

The sword weighs 2lbs 10 oz, but is very quick. {and of course its available}........

Programming tonite is a blade that will be "permanently assembled. Hope to send one to Christian Fletcher in about 4 weeks, as we kind of intend to do a few limilted production pieces {double fullered X}

Attachment: 41.32 KB

Attachment: 63.02 KB

Profile PM

Posts: 717 Location: Winchester, VA

Thu 31 May, 2007 6:29 pm

Nice to see you breaking new personal ground.

Were you able to take the lessons that you learned about dynamic handling from diamond/hexagonal shaped swords and apply them directly to the lenticular blade?

I don't know if you want to get into it but how did you "design" the sword? Did you start with a hexagonal blade and then grind the sword down differently or did you have to build the sword from the "ground up" as a lenticular design?

Profile PM

Posts: 870 Location: Seattle area

Thu 31 May, 2007 8:55 pm

Jason Elrod wrote:

Nice to see you breaking new personal ground.

Were you able to take the lessons that you learned about dynamic handling from diamond/hexagonal shaped swords and apply them directly to the lenticular blade?

I don't know if you want to get into it but how did you "design" the sword? Did you start with a hexagonal blade and then grind the sword down differently or did you have to build the sword from the "ground up" as a lenticular design?

Hi Jason

I'm not that paranoid about things............ the most outspoken folks on sword design either pretty much see things eye to eye, or have their own way of doing things anyways..........

Tinker handled this particular sword, and stated {on SFI for that matter} that it was his "favorite Atrim singlehander"......

So, the dynamic balance is there. Believe it or not, the section that is involved, the area betwixt fullers and tip, isn't going to influence things as much as the way the distal and profile tapers work together, the edge, and the overall blade geometry. Tang, pommel shape and weight.......... the fullering has more effect on the dynamic balance than the lenticular section of this particular blade.............

In fact, it handles very much like the DN1316, except maybe a bit quicker, maybe cuts a bit better........

Profile PM

Lafayette C Curtis

Posts: 2,698 Location: Indonesia

Fri 01 Jun, 2007 7:07 am

It looks like a borderline case between the XII and XIV to my eyes--but either way, it's impossible to mistake it for anything else than an ATrim monster cutter.

A lenticular blade. From Angus Trim. Sounds like a rather scary combination...

Profile PM

Posts: 967 Location: Michigan

Fri 01 Jun, 2007 8:15 am

What would one of those cost as a bare blade if you'd even offer it in that configuration?
Thanks,
Dan

Profile PM

Posts: 165 Location: Southeastern Pennsylvania

Fri 01 Jun, 2007 8:29 am

Your swords just keep getting better and more beautiful. Congratulations on this new development!

I would love to see you make a grossemesser - I'll do the polishing and rivet the handle on it myself if that will increase the probability of one being made. ;)

Good luck on this and all other endeavors.

Profile PM

M. Eversberg II

Posts: 1,435 Location: California, Maryland, USA

Fri 01 Jun, 2007 7:38 pm

Nice work! Is this part of your peened pommel series you where talking about last fall?

M.

Profile PM AIM YIM MSN ICQ

Posts: 9,557 Location: Dayton, OH

Sat 02 Jun, 2007 6:33 am

M. Eversberg II wrote:

Nice work! Is this part of your peened pommel series you where talking about last fall?

M.

In the forst post, Gus said:

Quote:

This sword, is what you might call a precursor. Its not "permanently assembled", but it has everything else that the permanently assembled swords will have.........

So it shares features with the peened series (aka permanently assembled), but is not peened.

Profile PM E-mail Website

Posts: 870 Location: Seattle area

Sat 02 Jun, 2007 10:29 am

Dan Dickinson wrote:

What would one of those cost as a bare blade if you'd even offer it in that configuration?
Thanks,
Dan

Hi Dan

I have six more machine payments left {$3600/mo}. After that, i might consider making bare blades for folks again, but right now I don't even want to think about it............

Profile PM

Posts: 870 Location: Seattle area

Sat 02 Jun, 2007 10:33 am

Chad Arnow wrote:

M. Eversberg II wrote:

Nice work! Is this part of your peened pommel series you where talking about last fall?

M.

In the forst post, Gus said:

Quote:

This sword, is what you might call a precursor. Its not "permanently assembled", but it has everything else that the permanently assembled swords will have.........

So it shares features with the peened series (aka permanently assembled), but is not peened.

Thanks Chad

With the disasters I've had since fall, I just haven't felt comfortable investing the time to finalize the "peened" stuff. What you see now, was pretty much done before November.

The actual peened series, will probably be a 2008 thing now.........

Profile PM

M. Eversberg II

Posts: 1,435 Location: California, Maryland, USA

Sun 03 Jun, 2007 1:37 am

Ah ok thanks Gus and Chad; totally missed that bit there. Makes sense now though.

Well, I am looking forward to your peened series; once we get a few reviews I shall see which one is the one I'm after.

M.

Profile PM AIM YIM MSN ICQ

Posts: 90

Tue 05 Jun, 2007 8:38 pm

Angus could you give us some more stats? Blade length and width in particular.

Profile PM

Posts: 1,606 Location: Chicago, Illinois

Tue 05 Jun, 2007 10:46 pm

This sword looks great. Sorry to hear about the peened line being pushed back until 2008. I'll keep my eyes open for it!

Profile PM

Posts: 870 Location: Seattle area

Wed 06 Jun, 2007 11:28 am

Darwin Todd wrote:

Angus could you give us some more stats? Blade length and width in particular.

Hi Todd

I'll dig things up, but I'm off right at the moment to ship this sword to Atlanta. It'll be at the Atlanta Blade Show at the Vaiiant Armory booth.........

Auld Dawg

Profile PM

Posts: 870 Location: Seattle area

Wed 06 Jun, 2007 12:09 pm

Tim Lison wrote:

This sword looks great. Sorry to hear about the peened line being pushed back until 2008. I'll keep my eyes open for it!

Hi Tim

Never know, if I get the right incentive, I might just finish this four fullered Type XIV blade I have in the next three to four weeks, peened.

Disasters derailed this part of "where I want to go", but I still intend to get there. Its part of establishing a new identity, if you will.

Instead of one of three US sword manufacturers, I really want to leave it two sword manufacturers {A&A and Albion}, and fit in between the manufacturers and the true custom guys. Small, 10 to15 swords a month, and maybe a couple knives or daggers. Improved on where I was last year......

Albion is at the top of the heap, makes great stuff, and with Mike as their customer support guy, have as good a customer support as they have a product........ Rather than butt heads with that, I'd rather be much smaller, make really good stuff that appeals to a different segment of the market. The tacticals are doing that for me now in a way, as I'm selling roughly 8 a month.

The kool thing about what Albion has done, is they've pushed the envelope on prices........ where a small operator like myself can fit in, improve on the past to justify mildly higher prices, and stay small........

That's why I want to do this peened series..........

Profile PM

Posts: 717 Location: Winchester, VA

Wed 06 Jun, 2007 4:12 pm

Angus Trim wrote:

I'll dig things up, but I'm off right at the moment to ship this sword to Atlanta. It'll be at the Atlanta Blade Show at the Vaiiant Armory booth.........
Auld Dawg

It's good to know that at least a couple of your blades are going to be there even if you can't attend. Can't wait to see them. Any chance that there's a 1403 in that batch?

Profile PM

Posts: 870 Location: Seattle area

Wed 06 Jun, 2007 9:24 pm

Jason Elrod wrote:

Angus Trim wrote:

I'll dig things up, but I'm off right at the moment to ship this sword to Atlanta. It'll be at the Atlanta Blade Show at the Vaiiant Armory booth.........
Auld Dawg

It's good to know that at least a couple of your blades are going to be there even if you can't attend. Can't wait to see them. Any chance that there's a 1403 in that batch?

Hi Jason

Not this year. There's only going to be five swords of mine there altogether. This one, and a bastard sword will be at the Valiant Armory Booth. As well as the Tac Gim. Tinker will have a Tac 23 Shortsword, and the Tac Gladius.......

That's all this year........next year I'm planning on attending.........

Profile PM

Page 1 of 1

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum

All contents © Copyright 2003-2006 myArmoury.com — All rights reserved
Discussion forums powered by phpBB © The phpBB Group
Switch to the Full-featured Version of the forum